We are exceptionally proud of our Maha dyno facility. Our dyno facility has now been completed and we are able to offer power runs and ECU mapping on one of the most advanced 4 wheel drive dyno systems on the market today. Our Maha MSR500 has been built within a purpose built cell. The services we offer on our dyno are outlined below.
This consists of carrying out a full throttle power test to determine bhp and torque at the wheels and calculated flywheel figures, at the same time where possible we will monitor boost and fuelling using exhaust gas analyzer and wideband lambda sensor we also have a external boost card to log boost where there isn’t available via OBD Our charge for a power run is £65 inc VAT.
Checks are carried out to ignition operation, fuelling system, engine management fault codes and live data with adjustments being made where possible. We then carry out a full throttle power test to determine bhp and torque at the wheels and calculated flywheel figures. Also, at the same time where possible we will monitor boost and fuelling using exhaust gas analyser and wideband lambda sensor. Our Dyno diagnostic labour rate of £120 per hour plus VAT will apply. This is separate to the cost of the power run. Where diagnostics are required to fault find our diagnostic labour rate of £75 per hour plus VAT will apply. This is separate to the cost of the power run. Prior to commencing a dyno run you will be asked to review our terms and conditions
To book a session on our dyno please contact us via phone or email. For further details on our mapping services please contact us.
We put a lot of consideration into investing in our dyno We explored a number of the American dynos which are significantly more cost effective. If we had wanted to produce headline numbers or run dyno days then these dynamometers probably would have been perfect. We also looked at the Australian manufacturer Dyno Dynamics a popular choice amongst many tuners in the UK. Like the American models this type of dyno is designed to measure power at the wheels and then uses a fixed multiplier to calculate the flywheel figure that many of our UK customers demand. However it is not a calculation method we have ever really agreed with due to the large grey area that can be misleading. The Maha MSR500 dyno is the same as that installed at Lamborghini, Porsche, VAG group, Toyota Motorsport and BMW M Devision, amongst other key players in the manufacturing sector.
We were aware from the off that the performance of the dyno cell surrounding the dynamometer is every bit as important as the dyno itself, if the readings derived from the dyno are to be considered useful and accurate. With this in mind, we conducted considerable research to ensure we could achieve the best possible set-up. To avoid heat soak and high intake air temperatures that can falsify readings especially during live mapping we have had our fresh air supply engineered to our specific requirements. Fresh air is drawn from outside via fabricated inlet and pipework into our MAHA fan so real world driving is simulated with fresh external air rather than warm polluted air from within a workshop environment. Exhaust emissions are taken care of via exhaust extraction to outside of the building this enables are for our cell to be used completely self contained.
Another great feature to help us quantify an improvement is the ability to time acceleration between various points. The dyno can calculate how quickly the car will now accelerate from 30-130mph in 5th or 20-70mph in 3rd, all with real-world load applied to the car. Not only does the dyno record these times but it can display them as a league table. This table then gets constantly updated each time the car passes through these two points. If, for example, we wanted to improve the power between 5,000rpm-6,000rpm we can set this as a timed window and accelerate through with the benefit of not having to start loading the car up from low rpms. This avoids creating unnecessary heat build-up and enables us to just plant the throttle from the same point making the runs consistent. This is a great tool for us to get the calibration close during live mapping sessions.
Braked Dynamometers work in a totally different way to Inertia Dyno’s (where most internet explanations are derived). As the title suggests, the vehicle is driving against a “braked roller”, a “strain gauge”, is attached between the brake and the chassis to measure force. A speed sensor is also attached to the axle of the dyno to measure shaft speed. Force (at the measuring gauge) x Speed (at the axle) = Power. We call this power P-Wheel as that is the industry recognised term. In the case of a MAHA Dynamometer, once the peak power is attained, the clutch is depressed and the vehicle starts to “coast down”, during the “coast down”, phase, the Dyno measures loss “P-Loss”, starting at the measuring gauge, right back to the clutch plate. This loss is displayed and added to the “P-Wheel”, in order to show “PEng” (Crank power), this has been proved time and again to be the accurate measure of power.